Slipper Socks Double IPA 5 Gallon

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 8.05ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

What’s better than slipper socks? Nothing really, but we found a way to make them even better. Put on your best pair of slipper socks and enjoy this amazing IPA. We wanted to clone one of or favorite beers from the Northeast, Heady Topper. If you have that beer then understand why we did it, if you have not then you need to brew this. Full of hop flavor and aroma this beer will blow the slipper socks right off your feet. If you are going to brew an IPA, then this is the IPA you need to brew.

$63.96 Regular Price $79.95
SKU
90-15499-05
Customize Slipper Socks Double IPA 5 Gallon

* Required Fields

Your Customization
Slipper Socks Double IPA 5 Gallon
Slipper Socks Double IPA 5 Gallon

In stock

Wishlist

$63.96

Summary

    WHAT YOU GET

    1 Can of Coopers Canadian Blonde HME

    2 Cans of Coopers Light Malt 

    2 Packets of BrewMax Booster

    6 Packets of Columbus Hops

    4 Packets of Simcoe Hops

    2 Packets of Centennial Hops

    1 Packet of US-05 Dry Ale Yeast

    3 Muslin Hop Sacks

    2 Packets of No-Rinse Cleanser


    FOR FANS OF

    The Alchemist Heady Topper


    BREW SPECS

    Flavor: Hoppy

    Original Gravity: 1.079

    Final Gravity: 1.015

    ABV: 8.4%

    SRM: (Color): 7

    IBU: (Bitterness): 79


    STEP 1: SANITIZING

    Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:

    1. Fill clean fermenter with 8 liters (2 Gallons) of warm water, then add 1 pack of No-Rinse Cleanser and stir until dissolved.

    2. Use your measuring cup to scoop the liquid up and run it down the side of the Coopers Fermenter. Do this around the entire fermenter a few times. Then add your krousen kollar and repeat. Then take some of the solution and pour it into the lid and allow it to sit for 2 minutes. (If you have a different fermenter sanitizing may be different.) 

    3. To clean the spigot, open it fully and allow the liquid to flow for 5 seconds, and then close.

    4. Pour some of the solution from the fermenter into a large bowl. You need enough to fully cover your brewing utensils. Place your spoon/whisk, can opener, and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in the cleaning solution prior to use. Any remaining solution in your fermenter can be discarded.

    5. After all, surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to the top of the fermenter, proceed immediately to brewing.


    STEP 2: BREWING

    Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.

    1. Remove the yeast packet from under the lid of the can of Brewing Extracts (not needed for this recipe), then place the 3 unopened cans in hot tap water.

    2. Place the packet of 2 packets of Columbus Hops and 2 Packets of Simcoe into a hop sack tying it closed, then trim away excess material.

    3. Add 1 gallon of water to your large pot. Add in both packets of Booster and mix until it is dissolved. Then add both cans of light UME and stir well to combine. Bring this mixture to a boil and add in the hopsack and let it boil for 10 minutes.

    4. While this is boiling take your second hopsack and add in 2 packets of Columbus Hops. Then add then add in 1 packet each of the packet of Centennial & Simcoe Hops to the hop sack tying it closed, then trim away excess material.

    5. Once 10 minutes have passed (step 3) remove the pot from heat. Add your second hop sack in. Then add in the Canadian blonde extract and mix until dissolved. Once dissolved cover the pot and let it sit for 30 minutes. This mixture of unfermented beer is called wort.

    6. When your 30 minutes is almost up, fill your fermenter with enough cold water to cover the spigot hole. Approximately 1-2 gallons of water.

    7. Pour the wort with the hop sacks into your fermenter, and then bring the volume of the fermenter to 19-liters or 5 gallons by adding more cold water.

    8. Stir your wort mixture vigorously with your sanitized spoon or whisk.

    9. Sprinkle the US-05 yeast packet into the fermenter, and place on the lid. Do not stir.

    Put your fermenter in a location with a consistent temperature between 68° and 78° F (20°-25° C), and out of direct sunlight. Ferment for 21 days.


    STEP 3: Dry-Hopping

    Dry hopping is the process of adding hops to a beer which will impart more hop flavor and aroma to your beer.

    1. On day 14 of Fermentation, you will add the remaining packets of Simcoe, Centennial, and Columbus Hops. Add all the hops into a sanitized hop sack and tie it closed so the hops have some room to flow freely. Carefully remove the lid from your fermenter and drop in the pellet hops. Quickly close the lid.


    STEP 4: BOTTLING & CARBONATING

    After 21 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (24 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.

    1. When your beer is ready to bottle, fill 3 1-gallon containers with warm water, then split the remaining pack of the No-Rinse Cleanser between them and mix until dissolved. Once dissolved, it is ready to use.

    2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.

    3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide. 

    4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.

    5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.

    6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation. 


    TIP FROM OUR BREWMASTERS

    After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it. 

    This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer

    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getReviews, 5.67ms
    • REVIEWS, PRODUCT
    • bvseo-msg: HTTP status code of 404 was returned; HTTP status code of 404 was returned;
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getContent, 6.28ms
    • QUESTIONS, PRODUCT
    • bvseo-msg: HTTP status code of 404 was returned;