Wicked Winter Warmer

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 13.31ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

A tasty way to warm up on a cold winter’s day, or any time. Dark roasted malt character takes the lead, but there is a deep underlying bitterness to off-set those flavors; mouthfeel is full, not thick like a stout but with enough body to stand up to the whiskey. The whiskey is the final note in the composition and brings the warmth that chases away the frostbite.

$24.95
SKU
90-15153-00
Customize Wicked Winter Warmer

* Required Fields

Your Customization
Wicked Winter Warmer
Wicked Winter Warmer

In stock

$24.95

Summary

    What You Get

    1 Can Winter Dark Ale Brewing Extract (HME)

    1 Packet of Dry Brewing Yeast (Under the Lid of the Brewing Extract)

    1 Packet of BrewMax LME Smooth

    1 Packet of No-Rinse Cleanser


    Your Provide

    11 Shots Whiskey of your choice -- (1 oz. (approx.) shot each per 740-mL bottle), shot size may vary by bottle, just be careful, too much may compromise the yeast and the resulting carbonation.


    Brew Specs

    Flavor: Malty

    Original Gravity: 1.059

    Final Gravity: 1.014

    ABV: 6.1% (For the beer only, ABV for whiskey will vary depending on amount and proof added.)

    SRM: (Color): 34

    IBU: (Bitterness): 60


    STEP 1: Sanitizing

    Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:

    1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.

    2.Screw on lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak solution. Allow to sit for at least 2 minutes and swirl again.

    3.To clean the spigot, open it fully and allow liquid to flow for 5 seconds and then close.

    4.Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in cleaning solution prior to using.

    5.After all surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to top of keg, proceed immediately to brewing.


    STEP 2: BREWING

    Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.

    1. Remove the yeast packet from under the lid of the can of brewing extract, then place the unopened can and LME softpack in hot tap water.

    2. Using the sanitized measuring cup, pour 4 cups of water into your clean 3-quart or larger pot.

    3. Bring mixture to a boil, then remove from heat. Open the can of Brewing Extract and the LME, pour contents into the hot mixture. Stir until thoroughly mixed. This mixture of unfermented beer is called wort.

    4. Fill your fermenter with cold tap water to the mark 1 on the back. If using any other fermenter this would be approximately 1 gallon of water.

    5. Pour the wort into your fermenter, and then bring the volume of the fermenter to mark 2 by adding more cold water. (If you have a different fermenter top it off with cold water to the 8.5-liter mark).

    6. Stir your wort mixture vigorously with your sanitized spoon or whisk.

    7. Sprinkle the yeast packet into the keg, and screw on the lid. Do not stir.

    Put your fermenter in a location with a consistent temperature between 65° and 76° F (20°-25° C), and out of direct sunlight. Ferment for 14 days.


    STEP 3: Bottling & Carbonating

    After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (17 total). At this point it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.

    1.When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use.

    2.Distribute the cleaning solution equally among the bottles. Screw on caps (or cover with metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solution into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.

    3.Once Bottles are santized add 1 shot of whiskey to each bottle

    4.Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide

    5.Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.

    6.Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.

    7.Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow to sit for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation. 


    Tip from our Brewmasters

    After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it. 

    This process is called conditioning and during this time the yeast left in your beer can help clean up any off flavors. Almost everything gets a little better with time and so will your beer.

    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getReviews, 2.42ms
    • REVIEWS, PRODUCT
    • bvseo-msg: HTTP status code of 404 was returned;