Mr. Beer's Blonde Shell Ale 5 Gallon
Looking for that ultimate light and refreshing beer for summer? Well, this is it! An easy-drinking Blonde Ale with all qualities you would find at any craft brewery. It's clean, well balanced, with a slight hop aroma and bitterness. This one will grow to be a staple brew in your beer supply.
WHAT YOU GET
1 Can of Coopers European Lager HME
5 Packets of BrewMax LME Pale
2 Packets of Carapils Malt
2 Packets of Pilsen Malt
2 Packets of Vienna Malt
1 Packet of Simcoe Hops
1 Packet of Cascade Hops
1 Packet of Citra Hops
1 Packet of Nottingham Ale Yeast
5 Muslin Hop Sacks
2 Packets of No-Rinse Cleanser
FOR FANS OF
Firestone Walker 805
Huss Brewing Scottsdale Blond
Original Gravity: 1.053
Final Gravity: 1.011
SRM: (Color): 6
IBU: (Bitterness): 30
STEP 1: SANITIZING
Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:
1. Fill clean fermenter with 8 liters (2 Gallons) of warm water, then add 1 pack of No-Rinse Cleanser and stir until dissolved.
2. Use your measuring cup to scoop the liquid up and run it down the side of the Coopers Fermenter. Do this around the entire fermenter a few times. Then add your krousen kollar and repeat. Then take some of the solution and pour it into the lid and allow it to sit for 2 minutes. (If you have a different fermenter sanitizing may be different.)
3. To clean the spigot, open it fully and allow the liquid to flow for 5 seconds, and then close.
4. Pour some of the solution from the fermenter into a large bowl. You need enough to fully cover your brewing utensils. Place your spoon/whisk, can opener, and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in the cleaning solution prior to use. Any remaining solution in your fermenter can be discarded.
5. After all, surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to the top of the fermenter, proceed immediately to brewing.
STEP 2: BREWING
Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.
1. Remove the yeast packet from under the lid of the can of Brewing Extract (you will not need this), then place the unopened can and LMEs in hot tap water.
2. Add all 6 packets of grains between 3 of the muslin sacks and tie them closed so that the grain can flow freely within the sacks. Set aside.
3. Add 8 cups of water to a 1 gallon or larger boil pot. Begin heating the water to a range of 155-165 degrees F and hold, at this range. Next, add the grain sacks into the water, and maintain the 155-165 temp for 30 minutes.
4. While you wait, add the packets of Simcoe and Cascade pellet hops into a hop sack and tie it closed.
5. After the 30-minute steep has completed, turn off the heat and remove the grain sacks from the pot and place them into a colander to drain, allowing the runoff to flow back into the pot, and rinse the grains with one cup of hot water (around 160 degrees), letting the excess runoff flow back into your pot. DO NOT squeeze the grain sacks. Once drained, discard the grain sacks.
6. Next, add in the 5 packets of LME and stir to combine. Bring mixture to a low, rolling boil.
7. Once the mixture is boiling add in the hop sack and let it boil for 15 minutes. Once 15 minutes is up remove the pot from the heat.
8. Open the HME can and add to the mixture in the pot and stir with a sanitized spoon until combined.
9. Fill your fermenter with enough cold water to cover the spigot hole. Approximately 1-2 gallons of water.
10. Pour the wort including the hop sack, into your fermenter, and then bring the volume of the fermenter to 5 gallons or 19 liters by adding more cold water.
11. Stir your wort mixture vigorously with your sanitized spoon or whisk.
12. Sprinkle the Nottingham brewing yeast packet into the fermenter, and place on the lid. Do not stir.
Put your fermenter in a location with a consistent temperature between 68° and 78° F, and out of direct sunlight. Ferment for 14 days.
STEP 3: Dry-Hopping
Dry hopping is the process of adding hops to a beer which will impart more hop flavor and aroma to your beer.
1. On day 12 of your 14-day fermentation, add the packet of Citra hops to a sanitized hopsack and carefully drop them into the fermenter. Allow the batch to ferment for 2 more days.
STEP 4: BOTTLING & CARBONATING
After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (14 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.
1. When your beer is ready to bottle, fill 3 1-gallon containers with warm water, then split the remaining pack of the No-Rinse Cleanser between them and mix until dissolved. Once dissolved, it is ready to use.
2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.
3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide.
4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.
5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.
6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation.
TIP FROM OUR BREWMASTERS
After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it.
This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer