Pumpkin Rising Spiced Amber Ale 5 Gallon

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 232.83ms
  • bvseo-msg: HTTP status code of 404 was returned;

Good gourd, almighty! This beer has that pie flavor and aroma that has been so elusive in many pumpkin beers. Baking the pumpkin to caramelize the flavors, then adding it and the spices after fermentation is complete really enhances the flavors so they shine most brightly against the malt backdrop. With a thick, creamy head and a lingering spice finish, this is truly a beer with which to celebrate the holidays in style!

Customize Pumpkin Rising Spiced Amber Ale 5 Gallon

* Required Fields

Your Customization
Pumpkin Rising Spiced Amber Ale 5 Gallon
Pumpkin Rising Spiced Amber Ale 5 Gallon

In stock

Subscription details




    1 Can Coopers Family Secret Amber Ale HME

    1 Can Coopers Amber Malt

    1 Packet of Booster

    1 Packet S-33 yeast

    2 Packets of No-Rinse Cleanser


    2 Cups of Brown Sugar

    2 Tbsp of Pumpkin Pie Spice

    16oz of Pumpkin Puree


    Samuel Adams Harvest Pumpkin Ale

    New Belgium Brewing Pumpkick


    Flavor: Balanced

    Original Gravity: 1.062

    Final Gravity: 1.016

    ABV: 6%

    SRM: (Color): 11

    IBU: (Bitterness): 30

    <hr> <h3><strong>STEP 1: Sanitizing</strong></h3> <p>Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. <strong>Make certain to clean all equipment that comes in contact with your beer by following the directions below:</strong></p> <p>1. Fill clean fermenter with 8 liters (2 Gallons) of warm water, then add 1 pack of No-Rinse Cleanser and stir until dissolved.</p> <p>2. Use your measuring cup to scoop the liquid up and run it down the side of the Coopers Fermenter. Do this around the entire fermenter a few times. Then add your krousen kollar and repeat. Then take some of the solution and pour it into the lid and allow it to sit for 2 minutes. (If you have a different fermenter sanitizing may be different.)&nbsp;</p> <p>3. To clean the spigot, open it fully and allow the liquid to flow for 5 seconds, and then close.</p> <p>4. Pour some of the solution from the fermenter into a large bowl. You need enough to fully cover your brewing utensils. Place your spoon/whisk, can opener, and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in the cleaning solution prior to use. Any remaining solution in your fermenter can be discarded.</p> <p>5. After all, surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to the top of the fermenter, proceed immediately to brewing.</p> <hr> <h3><strong>STEP 2: BREWING</strong></h3> <p>Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.</p> <p>1. Remove the yeast packet from under the lid of the can of the Secret Amber Brewing Extract, it's not needed for this recipe, then place both unopened cans in hot tap water.</p> <p>2. Using the measuring cup, pour 8 cups of water into your clean 3-quart or larger pot, then add in the brown sugar and Booster. Stirring constantly until the brown sugar and Booster are dissolved, bring water to a boil, then remove from heat.</p> <p>3. Open the cans of Brewing Extract and pour the contents into the hot mixture in your pot. Stir until thoroughly mixed. This mixture of unfermented beer is called wort.</p> <p>4. Fill your fermenter with enough cold water to cover the spigot hole. This is usually about a Gallon of water.</p> <p>5. Pour the wort into your fermenter, and then bring the volume of the fermenter up to 19 Liters by adding more cold water.</p> <p>6. Stir your wort mixture vigorously with your sanitized spoon or whisk.</p> <p>7. Sprinkle the S-33 yeast packet into the Fermenter, and place on the lid. Do not stir.</p> <p>Put your fermenter in a location with a consistent temperature between 65° and 76° F (20°-25° C), and out of direct sunlight. Ferment for 14 days.</p> <hr> <h3><strong>STEP 3: Adding Extras</strong></h3> <p>Adding extras is the process of adding additional ingredients to a beer that will impart more flavor and aroma to your finished brew.</p> <p>1. At the 1-week mark, sanitize your measuring spoon. Spread the pumpkin in a thin layer in a shallow pan and cover the pan with foil. Bake at 350° F for 30-45 minutes until the pumpkin begins to brown and the sugars caramelize, watch it carefully so it doesn't burn. Once the color and aroma are developed turn the oven off and allow the pan to remain inside until cooled to 70°F (about an hour). Once cool, mix the pumpkin pie spice with the pumpkin puree and carefully add it to your fermenter. Allow fermenting for 7 more days or until no longer sweet.</p> <hr> <h3><strong>STEP 4: Bottling &amp; Carbonating </strong></h3> <p>After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (17 total). At this point, it is time to bottle. <em>Do not let it sit in the fermenter for longer than 24 days total.</em></p> <p>1. When your beer is ready to bottle, fill 3 1-gallon containers with warm water, then split the remaining pack of the No-Rinse Cleanser between them and mix until dissolved. Once dissolved, it is ready to use.</p> <p>2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solution into a large bowl. Use this solution to clean any other equipment you may be used for bottling. Do not rinse.</p> <p>3. Add 2 <span style="text-decoration: underline;"><a href="https://www.mrbeer.com/mrbeer-carbonation-drops" target="_blank" rel="noopener">Carbonation Drops</a></span> to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using <a href="https://www.mrbeer.com/mrbeer-carbonation-drops" target="_blank" rel="noopener"><span style="text-decoration: underline;">this table as a guide</span></a>.&nbsp;</p> <p>4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.</p> <p>5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.</p> <p>6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation.&nbsp;</p> <div><hr></div> <h3><strong>Tip from our Brewmasters</strong></h3> <p>After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it.&nbsp;</p> <p>This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer.</p>
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getReviews, 7.41ms
    • bvseo-msg: HTTP status code of 404 was returned; HTTP status code of 404 was returned;
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getContent, 234.95ms
    • bvseo-msg: HTTP status code of 404 was returned;
    Search engine powered by ElasticSuite