Clovis Harvest Lager
A beer inspired by the harvest season and named after the first Frankish king, Clovis I. Light, crisp and refreshing with a low alcohol volume, you can drink this harvest lager all day and whistle while you work, if thats your "thing" of course... But that is up to you, my friend. Like Clovis himself, with this beer in your stein, you are the king! This is a true lager, meaning it must be cold fermented for best results.
WHAT YOU GET
2 packets Brewmax pale LME
1 packet Mr. Beer Smooth DME
1 packet pilsner malt
1 packet Carapils malt
1 packet Hersbrucker pellet hops
1 packet w-34/70 yeast
2 muslin hop sacks
1 no-rinse cleanser
FOR FANS OF
Maxlrainer- Ernte Hell
BREW SPECS
Flavor: Balanced
Original Gravity: 1.031
Final Gravity: 1.005
ABV: 3.4%
SRM: (Color): 4.2
IBU: (Bitterness): 21
STEP 1: SANITIZING
Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:
1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.
2. Screw on lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak solution. Allow to sit for at least 2 minutes and swirl again.
3. To clean the spigot, open it fully and allow liquid to flow for 5 seconds and then close
4. Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in cleaning solution prior to using.
5. After all surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to top of keg, proceed immediately to brewing.
STEP 2: BREWING
Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.
1. Add both packets of grains into one of the muslin sacks and tie it closed so that the grains can flow freely within the sack. Set aside.
2. Add 16 cups of water to a 2 gallon or larger boil pot. Begin heating the water to a range of 155-160 degrees F and hold, it at this range. Next, add the grain sack into the water, and maintain the 155-165 temp for 30 minutes.
3. While you wait, add the packet of Hersbrucker hops to one of the hopsacks and tie it closed so that the hops have room to expand and flow freely within the sack. Set aside
4. After the 30-minute steep has completed, turn off the heat and remove the grain sack from the pot and place it into a colander to drain, allowing the runoff to flow back into the pot, and rinse the grain with one cup of hot water (around 160 degrees), letting the excess runoff flow back into your pot. DO NOT squeeze the grain sack. Once drained, discard the grain sack.
5. Next, add in the packet of DME to the grain water, stir and bring this mixture to a boil. Allow the foam to rise, turning down the heat if it starts to get out of control. (you can also mist the foam with cold water in a spray bottle to quickly “kill it”) Once the foam naturally subsides, maintain a low rolling boil.
6. Once a steady and controlled boil is achieved, add both packets of LME and stir to combine.
7. Next, add in the hop sack that you prepared earlier and allow this to boil for a total of 30 minutes, stirring occasionally to avoid scorching.
8. After 30 minutes, remove the pot from the heat. Remove the hop sack from the wort with a sanitized spoon or tongs.
9. Fill your fermenter with cold water to mark 1 on the back. If using any other fermenter this would be approximately 1 gallon of water.
10. Pour the wort into your fermenter, and then bring the volume of the fermenter to mark 2 by adding more cold water. (If you have a different fermenter top it off to 8.5 liters)
11. Stir your wort mixture vigorously with your sanitized spoon or whisk.
12. Sprinkle the W-34/70 yeast packet into the keg, and screw on the lid. Do not stir.
Place your fermenter in a location with a consistent temperature between 55° and 65° and out of direct sunlight. Ferment for 14 days.
STEP 3: BOTTLING & CARBONATING
After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (17 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.
1. When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use
2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.
3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide.
4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.
5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.
6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation.
TIP FROM OUR BREWMASTERS
After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it.
This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer