Drop It Like A Scot Export Scottish Ale

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 229.55ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

If you are looking for the perfect brew to throw a few back and then drop it like a Scot then this is the perfect beer for you. This beer is malt forward with a soft mouthfeel. The perfect blend of hops and malt, this is a brew you can drink all night long to keep you dropping it low on the dance floor.

$29.95
SKU
90-15369-00
Customize Drop It Like A Scot Export Scottish Ale

* Required Fields

Your Customization
Drop It Like A Scot Export Scottish Ale
Drop It Like A Scot Export Scottish Ale

In stock

Subscription details
Wishlist

$29.95

Summary

    WHAT YOU GET

    1 Can American Lager HME

    1 Packet of Pale DME

    1 Packet of Smooth DME

    2 Packets of Fuggle Hops

    1 Packet S-04 yeast

    1 hop sacks

    1 Packet of No-Rinse Cleanser


    FOR FANS OF

    Scottish Ales


    BREW SPECS

    Flavor: Malty

    Original Gravity: 1.047

    Final Gravity: 1.012

    ABV: 4.6%

    SRM: (Color): 10

    IBU: (Bitterness): 25


    STEP 1: Sanitizing

    Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:

    1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.

    2. Screw-on the lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak the solution. Allow to sit for at least 2 minutes and swirl again.

    3. To clean the spigot, open it fully and allow the liquid to flow for 5 seconds, and then close.

    4. Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener, and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in a cleaning solution prior to use.

    5. After all, surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to the top of the keg, proceed immediately to brewing.


    STEP 2: BREWING

    Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.

    1. In a 2 gallon or larger pot, add 8 cups of water. Begin heating the pot to a low rolling boil. As the water is heating, sprinkle in the packets of DME, a little at a time, stirring between each addition. Continue stirring constantly to keep the rising foam in check, as the mixture comes to a boil. If foam begins to rise, pull the pan off the heat and lower the temperature slightly, continuing to stir (about 5 to 20 minutes depending on your particular conditions), until you hit the hot break which is where the foam has subsided, and the solution is now boiling. 

    2. Add both packets of Fuggle hops into a hop sack and tie it closed. Add the hop sack to your DME mixture and allow it to boil for 20 minutes. 

    3. After 20 minutes, remove the pot from the heat and add the can of American Lager HME, and stir until combined.

    4. Fill your fermenter with cold tap water to mark 1 on the back. If using any other fermenter this would be approximately 1 gallon of water.

    5. Pour the wort into your fermenter, and then bring the volume of the fermenter to mark 2 by adding more cold water. (If you have a different fermenter top it off to 8.5 liters).

    6. Stir your wort mixture vigorously with your sanitized spoon or whisk.

    7. Sprinkle the S-04 Dry brewing yeast packet into the keg, and screw on the lid. Do not stir.

    Put your fermenter in a location with a consistent temperature between 68° and 78° F, and out of direct sunlight. Ferment for 14 days.


    STEP 3: Bottling & Carbonating

    After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (17 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.

    1. When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use.

    2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solution into a large bowl. Use this solution to clean any other equipment you may be used for bottling. Do not rinse.

    3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide

    4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.

    5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.

    6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation. 


    Tip from our Brewmasters

    After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it. 

    This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer.

    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getReviews, 5.75ms
    • REVIEWS, PRODUCT
    • bvseo-msg: HTTP status code of 404 was returned; HTTP status code of 404 was returned;
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getContent, 231.91ms
    • QUESTIONS, PRODUCT
    • bvseo-msg: HTTP status code of 404 was returned;
    We found other products you might like!