Flatiron Trail Ale

Flatiron Trail Ale - Archived is rated 4.0 out of 5 by 2.
  • y_2024, m_7, d_15, h_4
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.42
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_1
  • loc_en_US, sid_90-15308-00, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_mrbeer
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 251.73ms

One of the best-known trails in our home state of Arizona, we wanted to provide a recipe that matched this trails beauty and something that you can drink on any hike for that matter! The perfect balance of hops and malt this easy-drinking ale is perfect for a long day pounding the trails and pounding some beers. 

Customize Flatiron Trail Ale

* Required Fields

Your Customization
Flatiron Trail Ale
Flatiron Trail Ale

In stock

Subscription details



    What You Get

    1 Oktoberfest Lager Brewing Extract (HME)

    2 Packets of Smooth DME

    1 Packet of Crystal Malt 60

    1 Packet of Red Wheat Flakes

    1 Packet of Nothern Brewer Hops

    1 Packet of Glacier Hops

    4 Muslin Hop Sack

    1 Packet of S-04 Yeast

    1 Packet of No-Rinse Cleanser

    For Fans Of

    Long Trail Brewing Company Long Trail Ale

    Brew Specs

    Flavor: Balanced

    Original Gravity: 1.051

    Final Gravity: 1.013

    ABV: 4.9%

    SRM: (Color): 15

    IBU: (Bitterness): 33


    Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:

    1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.

    2. Screw on lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak solution. Allow to sit for at least 2 minutes and swirl again.

    3. To clean the spigot, open it fully and allow liquid to flow for 5 seconds and then close

    4. Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in cleaning solution prior to using.

    5. After all surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to top of keg, proceed immediately to brewing.


    Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.

    1. Remove the yeast packet from under the lid of the can of Brewing Extract,(not needed for this
    recipe) then place the unopened can in hot tap water.

    2. Place both packets of grain into a muslin sack tying it closed, then trim away excess material.

    3. Place the Glacier Hops into its own hopsack and split the packet of Northern Brewer hops into
    2 hops sacks tying them closed, then trim away excess material.

    4. Add 8 cups of water to 1 gallon or larger pot. Heat the water until it reaches 155-160 degrees.
    Once the water has achieved this temperature range, add the grain sack so that it is fully
    submerged and maintain temperature range for 30 minutes.

    5. After 30 minutes has passed, take the pot off the heat, remove grain sack, and rinse it with 2
    cups of hot water using a colander or strainer while allowing the runoff to flow back into your
    pot. Discard grain sack.

    6. Slowly sprinkle in the packets of DME into the pot of cool water and stir to dissolve. Increase
    your heat to medium-high. Continue stirring constantly to keep the rising foam in check. If it
    begins to rise, pull the pan off the heat and lower the temperature slightly, continuing to stir
    (about 5 to 20 minutes depending on your particular conditions), until you hit the hot break
    which is where the foam has subsided and the solution is now boiling.

    7. Once you have a rolling boil add in one hopsack with the Northern Brewer Hops and let this
    boil for 60 minutes.

    8. Once 30 minutes of your 60 minutes have gone by add in the second hopsack with the
    Northern Brewer Hops.

    9. Once there are only 5 minutes left in your boil add in the last hopsack with the Glacier hops.
    Once the 5 minutes passes remove the pot from heat.

    10. Open the can of Brewing Extract and pour the contents into the hot mixture in your pot. Stir
    until thoroughly mixed. This mixture of unfermented beer is called wort.

    11. Fill your fermenter with cold tap water to the mark 1 on the back. If using any other
    fermenter this would be approximately 1 gallon of water

    12. Pour the wort into your fermenter, and then bring the volume of the fermenter to mark 2 by
    adding more cold water

    13. Stir your wort mixture vigorously with your sanitized spoon or whisk.

    14. Sprinkle the S-04 Dry Ale yeast packet into the keg, and screw on the lid. Do not stir. 

    Put your fermenter in a location with a consistent temperature between 68° and 78° F (20°-25°
    C), and out of direct sunlight. Ferment for 14 days.


    After 14 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (17 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.

    1. When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use

    2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.

    3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide. 

    4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.

    5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.

    6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation. 


    After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it. 

    This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer

    Rated 4 out of 5 by DoubleH32 from Good Fall Ale It is a good fall ale, but MRB does have better amber/brown ale recipes. I gave it 6-8 weeks conditioning before trying. Hop boil takes some time and really reduces down the DME grain mixture. As far a comparing it to the beer it is cloned after: darker, heavier and a little more bitter. I did a side by side taste (see picture). Color difference aside due to the extract, they taste similar I think the LT is lighter and would be easier to drink a lot of them. Overall a solid fall beer, would likely make again.
    Date published: 2020-12-06
    • y_2024, m_7, d_15, h_4
    • bvseo_bulk, prod_bvrr, vn_bulk_3.0.42
    • cp_1, bvpage1
    • co_hasreviews, tv_1, tr_1
    • loc_en_US, sid_90-15308-00, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
    • clientName_mrbeer
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getReviews, 9.08ms
    • bvseo_sdk, p_sdk, 3.2.1
    • CLOUD, getContent, 242.01ms
    • bvseo-msg: HTTP status code of 404 was returned;