PampelMUSE Grapefruit Hefeweizen
There is nothing quite like a wheat beer with any type of fruit added to it. They are just refreshing and easy to drink. However, when you add in grapefruit, it takes that to a whole new level. This wheat beer has all the amazing flavors you expect from a sold hefeweizen with the perfect about of grapefruit taste and aroma. This will be a must brew all summer long.
WHAT YOU GET
4 Packets of Golden LME
2 Packets of Lactose
1 Packet of Red Wheat Flakes
1 Packet of Carapils Malt
1 Packet of Honey Malt
1 Packet of Mt. Hood hops
1 Packet WB-06 yeast
2 hop sacks
1 Packet of No-Rinse Cleanser
16 ounces, good quality grapefruit juice
FOR FANS OF
Schofferhofer Grapefruit Hefeweizen
Original Gravity: 1.053
Final Gravity: 1.015
SRM: (Color): 6
IBU: (Bitterness): 7
STEP 1: SANITIZING
Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:
1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.
2. Screw on lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak solution. Allow to sit for at least 2 minutes and swirl again.
3. To clean the spigot, open it fully and allow liquid to flow for 5 seconds and then close
4. Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in cleaning solution prior to using.
5. After all surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to top of keg, proceed immediately to brewing.
STEP 2: BREWING
Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.
1. Add all 3 packets of grain into one of the muslin sacks and tie it closed so that the grain can flow freely within the sack and set aside. Next, add the packet of Mt. Hood hops to the second hops sack and tie it closed so the hops can flow freely within the sack. Set aside.
2. Add 8 cups of water to a 2 gallon or larger boil pot. Begin heating the water to a range of 155-160 degrees F and hold, at this range. Next, add the grain sack into the water, and maintain the 155-160 temp for 30 minutes.
3. After the 30-minute steep has completed, turn off the heat and remove the grain sack from the pot and place it into a colander to drain, allowing the runoff to flow back into the pot, and rinse the grain with one cup of hot water (around 160 degrees), letting the excess runoff flow back into your pot. DO NOT squeeze the grain sack. Once drained, discard the grain sack.
4. Next, add in all 4 packets of Golden LME and the two packets of lactose sugar to the grain water and stir thoroughly to combine.
5. Once mixed, increase the heat and bring the mixture to a boil, stirring occasionally to avoid scorching.
6. Once you have achieved a low, rolling boil, add in the hop sack containing the Mt. Hood hops and allow them to boil in the mixture for 30 minutes, stirring occasionally for 30 minutes.
7. After the 30-minute hop boil, remove the pot from the heat.
8. Fill your fermenter with cold water to mark 1 on the back. If using any other fermenter this would be approximately 1 gallon of water.
9. Pour the wort including the hop sack, into your fermenter, and then bring the volume of the fermenter to mark 2 by adding more cold water. (If you have a different fermenter top it off to 8.5 liters).
10. Stir your wort mixture vigorously with your sanitized spoon or whisk.
11. Sprinkle the WB-06 yeast packet into the keg, and screw on the lid. Do not stir.
Place your fermenter in a location with a consistent temperature between 70° and 75° F, and out of direct sunlight. Ferment for 14 days.
STEP 3: Adding Extras
Adding extras is the process of adding additional ingredients to a beer that will impart more flavor and aroma to your finished brew.
1. On Day 7 of fermentation, open the fermenter and quickly add the grapefruit juice. Screw on the lid and allow the beer to ferment for another 7 to 10 days.
STEP 4: BOTTLING & CARBONATING
After 21 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (24 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.
1. When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use
2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.
3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide.
4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.
5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.
6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation.
TIP FROM OUR BREWMASTERS
After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it.
This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer