Strawberry Belt Sour
A few sips of this beer will bring back the sweetest memories of your childhood when you just absolutely destroyed some strawberry belts. Drinking this beer tastes exactly like eating them, but with alcohol added so it’s even better! Don’t believe us? Brew it! This beer will change the way you think about sours.
WHAT YOU GET
1 Can of Golen Ale HME
1 Packet of Lactose
1 Bottle of Lactic Acid
1 Packet of US-05 Ale Yeast
1 Muslin Hop Sack
1 Packet of No-Rinse Cleanser
YOU PROVIDE
1lb. sour strawberry belt candies (any brand is fine, as long as they are NOT sugar-free).
FOR FANS OF
Bow & Arrow Brewing Co. Strawberry Amigo
BREW SPECS
Flavor: Fruity
Original Gravity: 1.057
Final Gravity: 1.008
ABV: 6.4%
SRM: (Color): 7
IBU: (Bitterness): 25
STEP 1: SANITIZING
Cleaning is one of the most important steps in brewing. It kills microscopic bacteria, wild yeast, and molds that may cause off-flavors in your beer. Make certain to clean all equipment that comes in contact with your beer by following the directions below:
1. Fill clean keg with warm water to line mark 1 on the back, then add ½ pack (about 1 tablespoon) of No-Rinse Cleanser and stir until dissolved. Once dissolved, the solution is ready to use. Save the remaining ½ of No-Rinse Cleanser because you will need it for bottling.
2. Screw on lid and swirl the keg so that the cleaning solution makes contact with the entire interior of the keg, including the underside of the lid. Note that the ventilation notches under the lid may leak solution. Allow to sit for at least 2 minutes and swirl again.
3. To clean the spigot, open it fully and allow liquid to flow for 5 seconds and then close
4. Pour the rest of the solution from the keg into a large bowl. Place your spoon/whisk, can opener and measuring cup into the bowl to keep them cleaned throughout the brewing process. Leave them immersed for at least 2 minutes in cleaning solution prior to using.
5. After all surfaces have been thoroughly cleaned, do not rinse or dry the keg or utensils. Return lid to top of keg, proceed immediately to brewing.
STEP 2: BREWING
Brewing beer is the process of combining a starch source (in this case, a malt brewing extract) with yeast. Once combined, the yeast eats the sugars in the malt, producing alcohol and carbon dioxide (CO2). This process is called fermentation.
1. Remove the yeast packet from under the lid of the can of Brewing Extract, then place the unopened can & LME in hot tap water.
2. Add 8 cups of water to a 1 gallon or larger boil pot.
3. Once boiling, add in the packet of lactose sugar and stir. Allow this mixture to boil for 5 minutes.
4. Remove the pot from heat and add the can of brewing extract. Stir with a sanitized spoon or whisk.
5. Fill your fermenter with cold tap water to mark 1 on the back. If using any other fermenter this would be approximately 1 gallon of water.
6. Pour the wort into your fermenter, and then bring the volume of the fermenter to mark 2 by adding more cold water. (If you have a different fermenter top it off to 8.5 liters)
7. Stir your wort mixture vigorously with your sanitized spoon or whisk.
8. Sprinkle the US-05 dry brewing yeast packet into the keg, and screw on the lid. Do not stir
Place your fermenter in a location with a consistent temperature between 68° and 75° F, and out of direct sunlight. Ferment for 14 days.
STEP 3: Adding Extras
Adding extras is the process of adding additional ingredients to a beer that will impart more flavor and aroma to your finished brew.
1. On day 7 of fermentation, using sanitized scissors, cut the strawberry belts into 1” – 2” pieces and place them into a sanitized Muslin sack (a quick boil in a cup or two of water will suffice).
2. Open your fermenter and carefully add in the sack of strawberry belts AND the bottle of lactic acid. Place the lid back on the fermenter and allow it to ferment for 7 more days.
STEP 4: BOTTLING & CARBONATING
After 21 days, taste a small sample to determine if the beer is fully fermented and ready to bottle. If it tastes like flat beer, it is ready. If it’s sweet, then it’s not ready. Let it ferment for 3 more days (24 total). At this point, it is time to bottle. Do not let it sit in the fermenter for longer than 24 days total.
1. When your beer is ready to bottle, fill a 1-gallon container with warm water, then add the remaining ½ pack of the No-Rinse Cleanser and stir until dissolved. Once dissolved, it is ready to use
2. Distribute the cleaning solution equally among the bottles. Screw-on caps (or cover with a metal cap if using glass bottles) and shake bottles vigorously. Allow to sit 10 minutes, then shake the bottles again. Remove caps and empty all cleaning solutions into a large bowl. Use this solution to clean any other equipment you may be using for bottling. Do not rinse.
3. Add 2 Carbonation Drops to each 740-mL bottle. For 1-liter bottles, add 2 ½ drops; for ½-liter bottles add 1 drop. Alternatively, you can add table sugar using this table as a guide.
4. Holding the bottle at an angle, fill each bottle to about 2 inches from the bottle’s top.
5. Place caps on bottles, hand tighten, and gently turn the bottle over to check the bottle’s seal. It is not necessary to shake them.
6. Store the bottles upright and out of direct sunlight in a location with a consistent temperature between 70°-76°F or 21°-24°C. Allow sitting for a minimum of 14 days. If the temperature is cooler than suggested it may take an additional week to reach full carbonation.
TIP FROM OUR BREWMASTERS
After the primary carbonation has taken place your beer is ready to drink. We recommend putting 1 bottle in the refrigerator at first for 48 hrs. After 48hrs. give it a try and if it is up to your liking put the rest of your beer in the fridge. If it does not taste quite right, leave the bottles out at room temp for another week or so. Keep following this method until your brew tastes just how you like it.
This process is called conditioning and during this time the yeast left in your beer can help clean up any off-flavors. Almost everything gets a little better with time and so will your beer